You Are Here :   Home  > > >  Accessories




Cone
Panel Diagrams Remarks
Metal Form A (m/m) B
  1. There are two diameters for inner units
    i.e. W5/16 and 3/8

  2. A - Panel thickness
    B - Inner unit diameter
For Metal W5/16
W3/8
Ply Wood Panel 12 W5/16
W3/8
16 W5/16
W3/8
24 W5/16
W3/8
Back to Top

  Plastic Cone For Beam

  Type D
  Inner Unit W1/2 is only used.
Back to Top

  Tapered P Cone   Bedding Plug
For the leaning panel constructure. It is used to seal the hole which is
made because the Cone is removed
after the concrete has set
Back to Top

ACCESSORY TOOLS
 FORMTIE Spanner  Box Spanner D and B

 To be used to fasten FORMTIE and Inner
 Unit and remove them.

 To be used to remove Cone.
Back to Top

U Clip
0.18kg
L Pin
0.4kg
Back to Top

OTHER ACCESSORIES
  L50 CONE   SLAB JOINTER
 L50 CONE  SLAB JOINTER

9mm
9mm, 12mm
Back to Top



Corner Chamfer

LIST OF STANDARD SIZES
  (1) Blue Corner Chamfer   (2) Blue Profile
Name Cross Section Quantity packed in 1 unit Name Cross Section Quantity packed in 1 unit
KT-10 250 KM-5 100
KT-15 200 KM-6 200
KT-15 100 KM-7 50
KT-20 100 KM-8 200
KT-20 200 KM-9 8
KT-25 100 KM-10
(Vertical Joint)		 50
KT-30 100 KM-11
(Horizontal Joint)		 200
KT-35 100 KM-12 100
KT-40 50 KM-13 100
KT-45 50 KM-14 100
KT-70 20 KM-15 100
KT-100 12 KM-16 100
KT-113 10 KM-17 50

KM-18 50
  Blue Joint
Name Cross Section Quantity packed in 1 unit KM-19 50
KM-1 200 KM-20 50
KM-2 100 KM-21 50
KM-3 50 KR-10 100
KM-4 100 KR-33 50
Back to Top



Shuttering Accessories
DROP-FORGED QUALITY FOR ALL SHUTTERING SYSTEMS
Indispensable: the Richee Tie-rod
An essential component among shuttering accessories is the Richee tie-rod. It matches all other items such as base plates, threaded base and header plates, wing nuts and hexagonal nuts.

DROP-FORGED QUALITY FOR ALL SHUTTERING SYSTEMS
The vote for long life material quality
Richee offers to the building industry a wide range of shuttering accessories of the highest accessories of the highest quality. Scaffolding couplers and shuttering components are mostly drop-forged, which offer significant advantages compared with accessories produced by other means.

Drop-forgings have considerably better material properties, such as the greater toughness and tensile strength necessary to fittings under dynamic stress. Drop-forged shuttering components will stand up much longer to hostile building site conditions owing to their greater wear resistance and they also offer the benefits of a markedly higher load factor.

  Tie-rod   Wing nut, two-wing

15 mm ø, load: P permissible
91 kN (DIN 18 216).
(Continuous thread, Dywidag dimensions)

Drop-forged
Material: C 35
Thread: 15 mm ø
Back to Top
  Anchor nut 100   Water barrier

Drop-forged
Material: C 35
Thread: 15 mm ø

Thread: 15 mm ø
Back to Top
  Water stop   Setting cone

Type G: cast iron

All galvanized and with movable contact rim, screw-in length restricted by stop pin, other cone dimensions upon request
Back to Top
  Hexagon nut, width across flats 30   Steel / plastic cone

Length: 105 mm
Thread: 15 mm ø

Thread: 15 mm ø with reinforced base edge to protect the shuttering
Cone casing material: St. 50.2 steel, galvanized
Length / width across flats: 100 / 30 mm
Back to Top
  Push-in cone   Plug

For tube supports
Material: PVC

For resealing tube supports
Material: PVC
Back to Top



Clamps & Pipe Accessories
PIPE ACCESSORIES / METAL FORM AND ACCESSORIES

48.6 Base
42.7 Base

48.6 Pipe joint
Jack base

42.7 Pipe joint

Expanding joint pin (Bone Joint)
Back to Top

SCAFFOLD CLAMP / PIPE CLAMP / END CLAMP
Scaffold Clamp (Fixed type) Pipe Clamp 60.5 X 48.6 Swivel clamp
Back to Top

End Clamp

Swivel type O (Vertical)
Swivel type O-1 (Horizontal)
Back to Top

Swivel type O-3
Swivel type O-1
Back to Top


For more information, please contact:
Tel: +65 6861 6808    Facsimile: +65 6861 7988    Email: info@richee.com.sg

Copyright 2004, Richee Engineering Enterprise Pte Ltd. All Right Reserved. Last updated on Apr 2004.